top of page

The new Maxwell Series Technical Ground is designed to be a multi-filtering tool for the average home.  Good earthing, from a technical standpoint for a home is based on the ground supplying a decent ohm impedance of 1 ohm of resistance or less – a good low ground impedance is based on outside soil conditions, and these conditions lessen overtime due to environmental form of acid washing.  Every time it rains or snows, the conductive elements within the soil are washed away or striped of their conductive properties.  It has gotten so bad, that now a quality ground for a home relies on conductive cements during installation to minimize the ohm resistance.  Without using these types of ground enhancement products during electrical installation, the average residential ground impedance ranges anywhere from 25 ohms up to 300 ohms of resistance depending on where you live in the country.  If you live in a salt free moist climate the ohm range will be between 35 ohms of resistance and 100 ohms of resistance.  If you live along the coast in a moist salt area, you can expect ohm ranges between 25 ohms and 75 ohms.  If you live in a drier climate the ohm ranges will be 100 ohms and higher.  If your property has a high-water table, you can expect ohm readings between 15 ohms and 30 ohms.  All these areas would significantly benefit from a quality ground enhancement product, but not all over-the-counter ground enhancement products are easy to install or do the job. 


If you scroll through YouTube videos, everyone and their brother makes themselves out to be an expert on low impedance/ohm resistance grounding using a wooden box filled of rocks.  Anyone that understands how to do this, knows a box of rocks is not going to cut it.  When quartz and tourmaline is used near an electric field – all metal case work star-grounding points drain off shorted AC or dc electrical fields either via physical leakage or magnetic leakage.  Both fields bonded to the box of rocks via the ground cable interact with the iron, carbon, and silicate elements within the rocks and force the rocks to vibrate as a piezoelectric filter.  Piezoelectric filters self-generate controlled sympathetic harmonic frequencies (a box of rocks has zero control over harmonics) which reflect to the metal case work and inject high frequency odd-harmonic distortion via the ground point into the component power supply isolated ground points.  A quality ground, based on Schumann principals should never become a high-pass filter (high frequency distortion) for the circuit.  A quality ground should be designed to roll off high frequencies within the analog band as low as possible by creating a lower ohm path of resistance for the circuit, the component, and the home.  A quality ground should put enough of inductive low frequency on the house ground to filter high frequency noise off the line, improve the rate of speed in order to drain the home of couple’s harmonics, RF, and EMI – rate of speed is dictated by ohms of resistance.  Another thing a quality ground should do, since we live in a wireless world, is to act as a centralized low frequency grounding point for all wireless traffic within the area of the grounding box.  A quality ground should be able to capture the electrical information, damp it down via internal piezoelectric filtration, and convert it to a lower state – IR is best.  Other grounding devices on the market place a small dc Schumann electrical charge on the component chassis via a direct connection and use the incoming power cord ground wire via the component star-ground point as the drain – this allows for no electrical charge build up and shocking when touched.  It does not work all the time because not every component or appliance uses the third wire safety ground – so be careful.


Our Maxwell Series Technical Ground follows the Schumann principal without applying the physical dc charge to the chassis.  The dc charge is a cheaper way to do what our Maxwell Technical Ground does without the charge.  By doing it our way, the Technical Ground becomes a multi-filter for any environment – I try to keep our specs conservative because everyone is living environment is different.  Some people might experience 100% improvement over our numbers, where someone else might only experience a 30% improvement.  Keep in mind the performance numbers we list below is the bare minimum that you can expect.


  • Helps to lower the house ground closer to .01 ohms of resistance.
  • Reduces stray RF and EMI associated with the house and component ground.
  • Acts as a central low frequency total home ground point for all ground based wireless distortion within 2000 sq. ft. of in-wall wiring.
  • Reduces stray in-room/home magnetic fields up to 20 sq. ft. (400 feet).
  • Filters and cleans in-home/room RF based Bluetooth signals up to 20 sq. ft (400 feet).
  • Converts most of the captured energy to IR and the remaining to a negative ion


NOTE: the negative ionic discharge is either converted to pure oxygen or hydrogen based on the humidity level of the surrounding area.  Negative ionic filtering is a great way to help regulate the atmosphere of the home.


What is inside the box that makes this so cool?


The Maxwell Series Technical Grounds start off with incorporating our Maxwell QPI in to the AC male plug – the Maxwell QPI uses our exclusive active ground to help maintain a clean low impedance frequency entering the Technical Ground.  The Maxwell QPI also incorporates our exclusive 7N silver dual inductive coil technology to help reduce harmonic ringing distortion on the circuit.  We use a custom 7ga. 6N copper helix ground cable to maintain a low impedance.  Inside the box we start with a 6N copper low impedance ground plane with our exclusive 100GHz 12 chamber piezoelectric infinity filter, a 5N copper 360-degree RF/EMI/EMR absorber, our exclusive 32 element conductive ionic ceramic, a dual layer negative charge filter, and a piezoelectric ionic filter.


 What are the benefits of our Maxwell Series Technical Ground?


Besides the lowering of harmonic distortion for everything plugged in to the home, other benefits include calmer mood based on the negative ionic discharge, fewer headaches, reduced colds, and joint pain.  People do not connect the dots of breathing issues or restless sleep to elevated in-home radiation sickness, but by reducing the radiation via the Technical Ground you will notice improved breathing over time, fewer allergy symptoms, less joint pain, and a more restful deep sleep without the need of over-the-counter-medication.  Things like melatonin production and testosterone are also reduced as the body absorbs low level radiation from our electrical and handheld personal devices – you will experience a major change in your health as your body adapts to the Technical Ground low energy environment that is established after a few days.


Installation is very simple… Plug the Maxwell Series Technical Ground into any open power receptacle within the room.  There are no active components inside the Technical Ground, everything is conductively charged inside the Technical Ground by the ground of the home.

Maxwell Series Technical Ground

    bottom of page